Backup Camera Monitor Mount & T-Bolt Adapter with 20mm Ball Mount

Solid built product! Honestly I was hoping that the bullet point t bolt for the monitor would be more secure, you just can’t tighten it enough it eventually falls to side because of the vibration! Still better than the suction cups one I had, even with an eh review I’d buy this again, and have recommended it already!

I needed to mount a dedicated always-on rearview camera in my RV to my sprinter windshield to monitor my tow vehicle. Everything I had seen looked terrible, suction cups, rubber bands, etc, these two parts allowed me to mount something that looked absolutely factory and clean. It doesn’t vibrate or bounce at all. I am extremely happy with it.

Only reason this didnt get 5 stars is because I am having difficulty keeping the camera tight. Maybe its operator error.

The original Haloview "T" mounting hardware that came with the BT7 has a 12mm wide head which fits perfectly in the back of the monitor. While this accessory will hold your Haloview monitor, it will rock from right to left. While this is not a huge issue, it doesn't meet in my opinion the quality standards you would expect from BP.

Fit my tuner fine need to file tuner opening very little.

Purchased Backup Camera Monitor Mount & T-Bolt Adapter with 20mm Ball Mount & Aluminum 15mm Connector End for Mounting Arm. Worked perfectly for my ProMaster van. Added monitor and rear view camera for full time view behind the van. Due to Forward Crash Detection and Lane Guidance electronics housed around existing arm for review mirror, I just removed the c-clip that holds the mirror to the 15mm ball mount. Added one of Bullet Point's 15mm Connector ends to replace the stock 20MM on the arm.

My husband and I are loving the BulletPoint mounting solution! We had to buy the mount for our Halo View BT7 camera system as the ball mount that came with it was too small for the BulletPoint mount. It just so happened that BulletPoint had a mount specifically for the Halo View monitor…it fit perfectly! Now our camping setup is complete…TPMS monitor, dash cam and camper camera system! There are so many configurations that we can do with the BulletPoint mounting system. I highly recommend this system!

I'm using this with an older Furrion RV camera setup. The flange on the T-bolt adapter goes in the slot but fits diagonally. However it works ok because you can tighten the collar to make a snug fit. You could make it fit exactly by trimming the flange about 1/16th inch but I believe it's secure enough without doing this.

Easy to install monitor not like what came with monitor.

Secures back up camera monitor without issue. Will recommend to others.

Awesome product. After many attempts of diy solutions I found this. This is my second vehicle with Bulletpoint products and I am always pleased. Thank you!!

I purchased this to mount my Haloview backup camera monitor since their mounting options were very limited. Much like other reviewers, the slot is wider than the T-slot adapter. No matter how much you crank down on it, it won’t be stable. My solution was to make a shim from a piece of paint stick. Took a lot of fitting but it’s solid.

2024 Jeep 392 we travel 275days out of the yr so far so good we have lots of BulletPoint we doing OffRoading trails all over the US for 2 months

Bought this for a Haloview camera monitor. The monitor pivots about 10° both directions. I tried tightening it with channel locks the see if it made a difference. The answer is no. Customer support was “very helpful” at acknowledging that the support prong was too small, with no options to remedy the situation. I would not recommend this product, and currently would not recommend BulletPoint.

Love this system.

They had to have seen these comments here and other places on this mount. This would be such a simple thing for them to address and provide a fairly cheap solution. Bottom line is the 12mm slot does slide into the Haloview BT7 (and other backup cam/tpms systems), but it allows for SIGNIFICANT rotating, which is not why I spent hundreds on bullet point mounting systems. This really cheapen's the whole system and why they don't address this is, I don't get.
I am going to try grinding/filing down the longer sides until it fits in the slot "width wise" instead of the narrower "height wise". I am sure that will resolve this, as I have every other art of the equation tightened down. I shouldn't have to do this with a system like this.
Design sna'foo #2, is zero knurling on the round dial to tighten against the back of the display. They have them smooth as a babies butt. And for me, I also use my BTS as a DVR for my 4 cameras (360 around the travel trailer) and I bring it inside when not driving. So easily loosening the tightening disc is quite difficult. So, I will be grinding out some poor-mans knurls around the disc, so I have a chance in h311 at removing and tightening it.
All in all, I love most of the stuff that bullet point makes, but there lack of addressing this ongoing issues with what should be a very simple solution is concerning to me.

Fit the screen for my travel trailer's back-up camera perfectly.

Works great thanks

Did not fit my backup camera monitor that came new with my 2024 Montana fifth wheel

Had to file down the sides to work with my mount but it works well

I could not keep the 20mm Ball tight on the T-Bolt. I think the problem is the steel bolt deforms the inside of the aluminum ball. I added a M5 Lock Nut to lock the bolt to the Ball, which solved the problem.

The product meets expectations. The fit and finish is very good. It anchored my Haloview monitor without issues. The only reason for 4 stars instead of 5, is its not easy to open the 12v receptacle that is available in the dash location. The bulletpoint base inhibits this.

Great product top quality does everything that it would